Screenshot (cap3): hazy or blurry texture spot on the pilot's window, just above dash on left.

Can you reset my key

Thanks

Paul

I'm using Air Manager to make a simple panel for my touch screen.

I'm using the DataRefTool Editor to locate the Commands and DataRefs. I have a few switches I'm not finding the Com & DataRef...... however, for this post, I'm working on the Eng Inlet Bypass switch.

xpl_dataref_subscribe("sim/cockpit/switches/anti_ice_inlet_heat","INT",EngInlet_change)
xpl_dataref_subscribe("sim/cockpit/switches/anti_ice_inlet_heat_per_engine", "INT[8]",EngInlet_change)
xpl_dataref_subscribe("sim/cockpit/switches/anti_ice_inlet_heat_per_enigne","INT[8]",EngInlet_change)
xpl_dataref_subscribe("sim/cockpit2/ice/ice_inlet_heat_on","INT",EngInlet_change)
xpl_dataref_subscribe("sim/cockpit2/ice/ice_inlet_heat_on_per_engine","INT[8]",EngInlet_change)

I know I can write to those dataref's but I think there might be an obscure Command that I should be using. as changing the value on each dataref individually doesn't change the switch position. 

I've searched under "inlet", "eng" and tried to actuate on every possible one that displayed, to no avail. searching for "bypass" returns no results.

when you have a minute or three, could you advise a newbie what Command I should be invoking ?

thank you

Dave

I also noticed that if you press a button or if an alarm sounds, you can hear it just as clearly outside as inside. This is also the case with the Pilatus PC-12, but at least it is quiet in the cabin.

Is this just me?

If not then can you please fix this in future updates.

Log_101420250937.txt SASLLog01.txt SASLLog02.txt

The lettering does not seem to be on the E1.png or E2.png textures and I cannot find it anywhere else.

Any suggestions?

Thanks in advance,

Marc

Has anyone used the Daher Kodiak 100 Panel Set from Experimental Sim Avionics? It mentions Thranda Xplane, but there are no returns. It looks like it would work well for Microsoft Flight Simulator. I see some instruments in Air Manaager but they are only Microsoft Flight Sim.

Experimental Sim Avionics

Sometimes when I am flying the Kodiak, the heading bug starts spinning around the dial. Clicking on the heading button or the heading selector doesn't seem to help.

In the past, I have been able to remedy this situation a couple of times, but have forgotten what I did to stop it spinning. If anybody can help me out with this it would be truly appreciated.

Thanks.

I really love your planes and especially the Daher/Quest Kodiak. Is there any chance you might do an upgrade to the Kodiak 900?

Quote

SASL3_T12

The Log.txt is attached.
The error message also mention a SASLLog.txt file, but I don't seems to be able to find it.
 

Regards,

Goup

Log.txt

Greg

Any advice would be very much appreciated please?

Richard S
ZS-RES

SkunkCraftsUpdater shows the message that "Some files are missing" but when I hit repair/update this messages appear in the log files

[SKUNKCRAFTS UPDATER INFO]: [LUA]: "module"    Processing X:\X-Plane Minimal/Aircraft/Thranda_Quest_Kodiak_v2/
[SKUNKCRAFTS UPDATER INFO]: [LUA]: "module"    X:\X-Plane Minimal/Aircraft/Thranda_Quest_Kodiak_v2/: Some files are missing or need to be repaired (138 bytes)
[SKUNKCRAFTS UPDATER INFO]: [LUA]: "module"    Failed to download X:\X-Plane Minimal/Aircraft/Thranda_Quest_Kodiak_v2/skunkcrafts_updater.cfg. Error : bad CRC32
[SKUNKCRAFTS UPDATER INFO]: [LUA]: "module"    X:\X-Plane Minimal/Aircraft/Thranda_Quest_Kodiak_v2/: Errors while repairing. Please check log

So what does this mean and what have I to do?

Regards,
Rinma

• I cannot activate the options panel for configuring the aircraft. I don't see where to activate it. At one time there was a Manual or something on the center consul but I don't see it any more. I must have done something to make it disappear.
• I cannot get the switches to work on the panels or the G1000
• I cannot get the panels to pop up.
• How do you activate the checklist.

Would appreciate any assistance.

Thank you!